High Energy Density Research Articles

Zwitterionic Cellulose-based Polymer Electrolyte Enabled by Aqueous Solution Casting for High-performance Solid-state Batteries.

Polyethylene oxide (PEO)-based solid-state batteries hold great promise as the next-generation batteries with high energy density and high safety. However, PEO-based electrolytes encounter certain limitations, including inferior ionic conductivity, low Li+ transference number, and poor mechanical strength. Herein, we aim to simultaneously address these issues by utilizing one-dimensional zwitterionic cellulose nanofiber (ZCNF) as fillers for PEO-based electrolytes using a simple aqueous solution casting method. Multiple characterizations and theoretical calculations demonstrate that the unique zwitterionic structure imparts ZCNF with various functions, such as disrupting PEO crystallization, dissociating lithium salts, anchoring anions through cationic groups, accelerating Li+ migration by anionic groups, as well as its inherent reinforcement effect. As a result, the prepared PL-ZCNF electrolyte exhibits remarkable ionic conductivity (5.37 × 10-4 S cm-1) and Li+ transference number (0.62) at 60 °C without sacrificing mechanical strength (9.2 MPa), together with high critical current density of 1.1 mA cm-2. Attributed to these merits of PL-ZCNF, the LiFePO4|PL-ZCNF|Li solid-state full-cell delivers exceptional rate capability and cycling performance (900 cycles at 5 C). Notably, the assembled pouch-cell can maintain steady operation over 1000 cycles with an impressive 93.7% capacity retention at 0.5 C and 60 °C, highlighting the great potential of PL-ZCNF for practical applications.

Stable Zinc Electrode Reaction Enabled by Combined Cationic and Anionic Electrolyte Additives for Non-Flow Aqueous Zn─Br2 Batteries.

Aqueous zinc-bromine batteries hold immense promise for large-scale energy storage systems due to their inherent safety and high energy density. However, achieving a reliable zinc metal electrode reaction is challenging because zinc metal in the aqueous electrolyte inevitably leads to dendrite growth and related side reactions, resulting in rapid capacity fading. Here, it is reported that combined cationic and anionic additives in the electrolytes using CeCl3 can simultaneously address the multiple chronic issues of the zinc metal electrode. Trivalent Ce3+ forms an electrostatic shielding layer to prevent Zn2+ from concentrating at zinc metal protrusions, while the high electron-donating nature of Cl- mitigates H2O decomposition on the zinc metal surface by reducing the interaction between Zn2+ and H2O. These combined cationic and anionic effects significantly enhance the reversibility of the zinc metal reaction, allowing the non-flow aqueous Zn─Br2 full-cell to reliably cycle with exceptionally high capacity (>400mAh after 5000 cycles) even in a large-scale battery configuration of 15×15cm2.

Recent advances and understanding of high-entropy materials for lithium-ion batteries.

Lithium-ion batteries (LIBs) has extensively utilized in electric vehicles and portable electronics due to their high energy density and prolonged lifespan. However, the current commercial LIBs are plagued by relatively low energy density. High-entropy materials with multiple components have emerged as an efficient strategic approach for developing novel materials that effectively improve the overall performance of LIBs. This article provides a comprehensive review the recent advancements in rational design of innovative high-entropy materials for LIBs, as well as the exceptional lithium ion storage mechanism for high-entropy electrodes and considerable ionic conductivity for high-entropy electrolytes. This review also analyses the prominent effects of individual components on the high-entropy materials' exceptional capacity, considerable structural stability, rapid lithium ion diffusion, and excellent ionic conductivity. Furthermore, this review presents the synthesis methods and their influence on the morphology and properties of high-entropy materials. Ultimately, the remaining challenges and future research directions are outlined, aimed at developing more effective high-entropy materials and improving the overall electrochemical performance of LIBs.

Glycerol Triacetate-Based Flame Retardant High-Temperature Electrolyte for the Lithium-Ion Battery.

Rechargeable batteries that can operate at elevated temperatures (>70 °C) with high energy density are long-awaited for industrial applications including mining, grid stabilization, naval, aerospace, and medical devices. However, the safety, cycle life, energy density, and cost of the available high-temperature battery technologies remain an obstacle primarily owing to the limited electrolyte options available. We introduce a flame-retardant electrolyte that can enable stable battery cycling at 100 °C by incorporating triacetin into the electrolyte system. Triacetin has excellent chemical stability with lithium metal, and conventional cathode materials can effectively reduce parasitic reactions and promises a good battery performance at elevated temperatures. Our findings reveal that Li-metal half-cells can be made that have high energy density, high Coulombic efficiency, and good cycle life with triacetin-based electrolytes and three different cathode chemistries. Moreover, the nail penetration test in a commercial-scale pouch battery using this new electrolyte demonstrated suppressed heat generation when the cell was damaged and excellent safety when using the triacetin-based electrolyte.

Design Principles and Routes for Calcium Alkoxyaluminate Electrolytes.

Multivalent-ion battery technologies are increasingly attractive options for meeting diverse energy storage needs. Calcium ion batteries (CIB) are particularly appealing candidates for their earthly abundance, high theoretical volumetric energy density, and relative safety advantages. At present, only a few Ca-ion electrolyte systems are reported to reversibly plate at room temperature: for example, aluminates and borates, including Ca[TPFA]2, where [TPFA]- = [Al(OC(CF3)3)4]- and Ca[B(hfip)4]2, [B(hfip)4]2- = [B(OCH(CF3)2)4]-. Analyzing the structure of these salts reveals a common theme: the prevalent use of a weakly coordinating anion (WCA) consisting of a tetracoordinate aluminum/boron (Al/B) center with fluorinated alkoxides. Leveraging the concept of theory-aided design, we report an innovative, one-pot synthesis of two new calcium-ion electrolyte salts (Ca[Al(tftb)4]2, Ca[Al(hftb)4]2) and two reported salts (Ca[Al(hfip)4]2 and Ca[TPFA]2) where hfip = (-OCH(CF3)2), tftb = (-OC(CF3)(Me)2), hftb = (-OC(CF3)2(Me)), [TPFA]- = [Al(OC(CF3)3)4]-. We also reveal the dependence of Coulombic efficiency on their inherent propensity for cation-anion coordination.

Carbon/C3N4 heterostructures constructed from lignin toward enhanced lithium-ion storage

Lithium-ion batteries (LIBs) are widely used in portable energy storage. The capacity of commercial graphite is difficult to improve due to the stoichiometry limit of LiC6 of graphite, thus new anodes need to be developed to meet the demand of high-energy–density LIB. The growing interest in graphitized carbon nitride (g-C3N4) stems from its structural resemblance to graphite and its capacity to offer abundant adsorption and intercalation sites. However, g-C3N4, as a semiconductor, has a low lithium transfer rate due to its poor conductivity and high diffusion resistance. Improving the electron transport rate of g-C3N4 and reducing the adsorption energy barrier of Li+ in g-C3N4 are the keys to improving the electrochemical performances of g-C3N4. In this study, lignin and melamine were homogeneously mixed using the spray drying method, followed by the preparation of covalently bonded C3N4/LC material through a one-step carbonization process. The uniform dispersion of g-C3N4 in amorphous carbon can improve the conductivity and reduce the diffusion energy barrier of Li+. As a result, the C3N4/LC-x anode has better electrochemical behavior, including higher reversible capacity, better rate performance, and cycle stability.

High-energy density cellulose nanofibre supercapacitors enabled by pseudo-solid water molecules

Compared with conventional electrochemical supercapacitors and lithium-ion batteries, the novel amorphous cellulose nanofibre (ACF) supercapacitor demonstrates superior electric storage capacity with a high-power density, owing to its fast-charging capability and high-voltage performance. This study unveils introduces an ACF supercapacitor characterised by a substantial energy density. This is achieved by integrating a singular layer of pseudo-solid water molecules (electrical resistivity of 1.11 × 108 Ω cm) with cellulose nanofibers (CNFs), establishing forming an electric double layer at the electrode interface. The enhanced energy storage in these high-energy density capacitors (8.55 J/m2) is explicated through the polarisation of protons and lone pair electrons on oxygen atoms during water electrolysis, commencing at 1.23 V. Improvements in energy density are attainable through CNF density enhancements and charging-current optimisation. The proposed ACF supercapacitor offers substantial promise for integration into the power sources of flexible and renewable paper-based electronic devices.

Phosphorus‐based anodes for fast‐charging alkali metal ion batteries

AbstractAdvancing fast‐charging technology is an important strategy for the development of alkali metal ion batteries (AMIBs). The exploitation of a new generation of anode material system with high‐rate performance, high capacity, and low risk of lithium/sodium/potassium plating is critical to realize fast‐charging capability of AMIBs while maintaining high energy density and safety. Among them, phosphorus‐based anodes including phosphorus anodes and metal phosphide anodes have attracted wide attention, due to their high theoretical capacities, safe reaction voltages, and natural abundance. In this review, we summarize the research progress of different phosphorus‐based anodes for fast‐charging AMIBs, including material properties, mechanisms for storing alkali metal ions, key challenges and solution strategies for achieving fast‐charging capability. Moreover, the future development directions of phosphorus‐based anodes in fast‐charging AMIBs are highlighted.image

Potential of Aluminum as a Metal Fuel for Supporting EU Long‐Term Energy Storage Needs

AbstractThe EU's energy transition necessitates availability of green energy carriers with high volumetric energy densities for long‐term energy storage (ES) needs. A fully decarbonized scenario considering renewable energy availability is analyzed underpinning the need for such carriers. Considering the shortcomings of Power‐to‐X technologies in terms of efficiency and low volumetric density, Aluminum (Al) is identified as a potential alternative showing significantly high volumetric energy densities (23.5 kWh L−1). In this paper, an Al‐based long‐term ES concept is investigated, taking advantage of the inherent recycling of the active species (i.e., Al2O3 to Al) coupling decarbonized Hall–Héroult process with an Al‐steam oxidation for simultaneous hydrogen (H2) and heat generation. This work demonstrates an innovative lab‐scale fine Al powder‐steam oxidation process at ≈900 °C without use of catalysts or additives, exploiting alumina as inert material. Conducted SEM‐EDX analysis on oxidized Al provides supporting evidence in favor of employed oxidation pathway, hindering tendency of aluminum oxide (Al2O3) clumping and enabling direct use of oxides in the smelting process for fully recyclability. Moreover, outcomes of XRD analyses are presented to validate the measured total H2 yields.

Bending, electroadhesion and sensing performances of single compliant electrode dielectric elastomer actuator based on SEBS gel

Abstract Dielectric elastomer actuators (DEAs) have great potential for application in soft robotics due to their ability to undergo substantial deformations, rapid response times, and high energy density when subjected to external electrical stimuli. However, the application of DEAs in the field of soft grippers is limited by their restricted direct electro-bending capability, output force, self-sensing capacity, and pre-stretching requirement. In this study, we fabricated a single compliant electrode dielectric elastomer actuator (SCE-DEA) which was made by sandwiching a compliant electrode between two layers of poly(styrene-b-ethylene-co-butylene-b-styrene) (SEBS)/white mineral oil (WO) dielectric elastomer films. The SCE-SEBS/WO was demonstrated to have the capacities of bending, sensing, and electroadhesion. The SCE-SEBS/WO can be used in various soft actuator modes, such as the unipolar electroadhesion actuator, soft gripper, and soft vibrator. The grabbing mechanism of SCE-SEBS/WO-based soft grippers with opposite bipolar configuration is caused by electric field induced bending of SEC-SEBS/WO and subsequent electrostatic attraction between both SEC-SEBS/WO. The SEC-SEBS/WO based soft grippers have rapid response detachment, and ability to grasp various types of objects. Three-layer stacked SCE-SEBS/WO-60 (with 60 wt% of WO) exhibited 531 mN/cm2 of electroadhesion stress on the paper at 3.0 kV applied voltage, and the soft gripper made by four SCE-SEBS/WO-60 can successfully grab wood blocks weighing 162.4 g at 5 kV applied voltage. The sensing capacity of SCE-SEBS/WO based soft gripper was based on the bending strain dependent resistance changes of the compliant electrode. Our results provide new insights into the fabrication of DEA based soft grippers.

Examining a hadronic γ-ray scenario for the radiative shell and molecular clouds of the old GeV supernova remnant G298.6−0.0

Abstract Based on the 13.7 yr Fermi-LAT data, Yeung, Bamba, and Sano (2023, PASJ, 75, 384) claimed detection of two γ-ray sources (namely Src-NE and Src-NW) associated with the supernova remnant (SNR) G298.6−0.0, and interpreted it as an old GeV SNR interacting with molecular clouds (MCs). In this follow-up study, we refine the flux measurements below 2 GeV with Fermi-LAT event types of better angular reconstruction. Then, we report our γ-ray spectral fittings and cosmic-ray phenomenology in a hadronic scenario, considering both the shell and MC regions of SNR G298.6−0.0. We confirm that the γ-ray spectra of both Src-NE and Src-NW exhibit spectral breaks, at $1.50_{-0.50}^{+0.60}$ and $0.68_{-0.11}^{+0.32}\:$GeV, respectively. Src-NW has a harder broad-band photon index than Src-NE, suggesting an appreciable difference between the physical separations of their respective emission sites from SNR G298.6−0.0. The cosmic-ray spectrum responsible for Src-NE starts with a minimum energy $E_\mathrm{CR,min}=1.38_{-0.16}^{+0.47}\:$GeV, and has a proton index $\Gamma _\mathrm{CR}=2.57_{-0.21}^{+0.18}$ below the exponential cutoff energy $E_\mathrm{CR,max}=240_{-150}^{+240}\:$GeV. Accordingly, we argue that Src-NE is dominated by the SNR shell, while only a minor portion of lower-energy emission is contributed by the MCs interacting with the SNR. The cosmic-ray population for Src-NW starts at a higher energy such that the ECR, min ratio of Src-NW to Src-NE is ≳2. The high ECR, min, as well as the high cosmic-ray energy density required (∼26 eV cm−3), supports the interpretation that Src-NW is predominantly the γ-ray emission from the farther MCs being bombarded by protons that had earlier escaped from SNR G298.6−0.0. By comparing the high-energy features of G298.6−0.0 with those of analogical SNRs, especially SNR W 28 and SNR W 44, we further constrain the age of SNR G298.6−0.0 to be 10–30 kyr, under the assumption of a purely hadronic scenario.

Iron as recyclable metal fuel: Unraveling oxidation behavior and cyclization effects through thermogravimetric analysis, wide-angle X-ray scattering and Mössbauer spectroscopy.

The carbon-free chemical storage and release of renewable energy is an important task to drastically reduce CO2 emissions. The high specific energy density of iron and its recyclability makes it a promising storage material. Energy release by oxidation with air can be realized by the combustion of micron-sized iron powders in retro-fitted coal fired power plants and in fixed-bed reactors under milder conditions. An experimental parameter study of iron powder oxidation with air was conducted based on thermogravimetric analysis in combination with wide-angle X-ray scattering and Mössbauer spectroscopy. In agreement with literature the oxidation was found to consist of a very fast initial oxidation of the outer particle layer followed by much slower oxidation due to diffusion of iron ions through the Fe2O3/Fe3O4 layer being the ratelimiting step. Scanning electron microscopy analysis of the iron particle before and after oxidation reveal a strong particle morphology transformation. This impact on the reaction was studied by cyclization experiments. Up to 10 oxidation-reduction cycles show that both, oxidation and reduction rates, increase strongly with cycling due to increased porosity.

A Cu/MnOx Composite with Copper-Doping-Induced Oxygen Vacancies as a Cathode for Aqueous Zinc-Ion Batteries.

Aqueous zinc-ion batteries are anticipated to be the next generation of important energy storage devices to replace lithium-ion batteries due to the ongoing use of lithium resources and the safety hazards associated with organic electrolytes in lithium-ion batteries. Manganese-based compounds, including MnOx materials, have prominent places among the many zinc-ion battery cathode materials. Additionally, Cu doping can cause the creation of an oxygen vacancy, which increases the material's internal electric field and enhances cycle stability. MnOx also has great cyclic stability and promotes ion transport. At a current density of 0.2 A g-1, the Cu/MnOx nanocomposite obtained a high specific capacitance of 304.4 mAh g-1. In addition, Cu/MnOx nanocomposites showed A high specific capacity of 198.9 mAh g-1 after 1000 cycles at a current density of 0.5 A g-1. Therefore, Cu/MnOx nanocomposites are expected to be a strong contender for the next generation of zinc-ion battery cathode materials in high energy density storage systems.

Review of the Real-Time Monitoring Technologies for Lithium Dendrites in Lithium-Ion Batteries

Lithium-ion batteries (LIBs) have the advantage of high energy density, which has attracted the wide attention of researchers. Nevertheless, the growth of lithium dendrites on the anode surface causes short life and poor safety, which limits their application. Therefore, it is necessary to deeply understand the growth mechanism of lithium dendrites. Here, the growth mechanism of lithium dendrites is briefly summarized, and the real-time monitoring technologies of lithium dendrite growth in recent years are reviewed. The real-time monitoring technologies summarized here include in situ X-ray, in situ Raman, in situ resonance, in situ microscopy, in situ neutrons, and sensors, and their representative studies are summarized. This paper is expected to provide some guidance for the research of lithium dendrites, so as to promote the development of LIBs.

The synergy mechanism of CsSnI3 and LiTFSI enhancing the electrochemical performance of PEO‐based solid‐state batteries

AbstractLithium metal solid‐state battery is the first choice of batteries for electromobiles and consumer electronic products because of the specific capacity of 3860 mAh g−1 and high electrochemical potential (−3.04 V) of Li metal. Flexible polymer solid electrolytes have become the optimal solution to produce high energy density lithium batteries with arbitrary size and shape. In this work, we introduce a halide perovskite, CsSnI3, into the polyethylene oxide/lithium bis‐(trifluoromethanesuphone)imide (PEO–LiTFSI) polymer matrix. The CsSnI3 could form a LixSn alloy with Li, leading to homogenization of the electric field and Li+‐flux at the interface, Sn atom also bonds with the TFSI− anion to provide more dissociated Li+. Besides that, the I atom could interact with Li to form an electronic insulation with a strong blocking effect on electron tunneling. As a proof of concept, the synergy mechanism of the PEO–LiTFSI–CsSnI3 electrolyte improves the stable cycle life of the symmetric battery to more than 500 h, and the Li+ conductivity raised to 6.1 × 10−4 S cm−1 at 60°C. The application of the “zwitter ions analog” halide perovskite in PEO–LiTFSI provides a new choice among various methods to improve the electrochemical performance of polymer solid‐state batteries.

Flexible Aluminum-Air Battery Based on High-Performance Three-Dimensional Dual-Network PVA/KC/KOH Composite Gel Polymer Electrolyte.

With a large theoretical capacity and high energy density, aluminum-air batteries are a promising energy storage device. However, the rigid structure and liquid electrolyte of a traditional aluminum-air battery limit its application potential in the field of flexible electronics, and the irreversible corrosion of its anode greatly reduces the battery life. To solve the above problems, a PVA/KC/KOH (2 M) composite gel polymer electrolyte (GPE) with a three-dimensional dual-network structure consisting of polyvinyl alcohol (PVA), kappa-carrageenan (KC), and potassium hydroxide was prepared in this paper by a simple two-step method and applied in aluminum-air batteries. At room temperature, the ionic conductivity of the PVA/KC/KOH (2 M) composite GPE was found to be up to 6.50 × 10-3 S cm-1. By utilizing this composite GPE, a single flexible aluminum-air battery was assembled and achieved a maximum discharge voltage of 1.2 V at 5 mA cm-2, with discharge time exceeding 3 h. Moreover, the single flexible aluminum-air battery maintains good electrochemical performance under various deformation modes, and the output voltage of the battery remains at about 99% after 300 cycles. The construction of flexible aluminum-air batteries based on a three-dimensional dual-network PVA/KC/KOH composite GPE provides excellent safety and high-multiplication capabilities for aluminum-air batteries, making them potential candidates for various flexible device applications.

A Volcano Correlation between Catalytic Activity for Sulfur Reduction Reaction and Fe Atom Count in Metal Center.

Sulfur reduction reaction (SRR) facilitates up to 16 electrons, which endows lithium-sulfur (Li-S) batteries with a high energy density that is twice that of typical Li-ion batteries. However, its sluggish reaction kinetics render batteries with only a low capacity and cycling life, thus remaining the main challenge to practical Li-S batteries, which require efficient electrocatalysts of balanced atom utilization and site-specific requirements toward highly efficient SRR, calling for an in-depth understanding of the atomic structural sensitivity for the catalytic active sites. Herein, we manipulated the number of Fe atoms in iron assemblies, ranging from single Fe atom to diatomic and triatomic Fe atom groupings, all embedded within a carbon matrix. This led to the revelation of a "volcano peak" correlation between SRR catalytic activity and the count of Fe atoms at the active sites. Utilizing operando X-ray absorption and X-ray diffraction spectroscopies, we observed that polysulfide adsorption-desorption and electrochemical conversion kinetics varied up and down with the incremental addition of even a single iron atom to the catalyst's metal center. Our results demonstrate that the metal center with exactly two iron atoms represents the optimal configuration, maximizing atom utility and adeptly handling the conversion of varied intermediate sulfur species, rendering the Li-S battery with a high areal capacity of 23.8 mAh cm-2 at a high sulfur loading of 21.8 mg cm-2. Our results illuminate the pivotal balance between atom utilization and site-specific requirements for optimal electrocatalytic performance in SRR and diverse electrocatalytic reactions.

Quality of black pellets of charcoal fines produced with different moisture content and drying time

Charcoal fines are co-products of the wood carbonization process, unwanted because they reduce the gravimetric yield of the main product, charcoal. It can be produced due to the carbonization process, during the storage and transport of charcoal. Pelletizing charcoal fines increases the energy density of this material, producing a homogeneous fuel with lower moisture content, enabling burning in equipment with high energy efficiency, in addition to desirable properties in energy products such as high fixed carbon content and low moisture content. This study evaluated the effect of moisture content and drying time on the production of black pellets from charcoal fines bound with rice starch (Oryza sativa) on the physicochemical and mechanical characteristics. Black pellets were produced using two proportions of water (10 or 20%) and a drying time of 4 or 6 hours. Black pellets were evaluated for their proximate analysis, elemental composition, moisture content, size, apparent density, calorific value and energy density. The addition of water did not affect the content of volatile matter, ash, and fixed carbon, while the treatment with addition of 20% water and four hours of drying showed a higher moisture content (3.34%). The addition of water allowed for better heat conduction and particle arrangement, producing pellets with a durability greater than 98%. The better arrangement promoted by the addition of 20% water also increased the density of the pellets, resulting in greater energy density. Black pellets can be considered an alternative for residential heating, with T3 treatment (20% - 4h) with a high energy density and better performance in terms of desirable properties for use and commercialization according to the standard EN 14961-6.

Rational Design of Local Reaction Environment for Electrocatalytic Conversion of CO2 into Multicarbon Products

AbstractThe electrocatalytic conversion of CO2 into multi‐carbon (C2+) products provides an attractive route for storing intermittent renewable electricity as fuels and feedstocks with high energy densities. Although substantial progress has been made in selective electrosynthesis of C2+ products via engineering the catalyst, rational design of the local reaction environment in the vicinity of catalyst surface also acts as an effective approach for further enhancing the performance. Here, we discuss recent advances and pertinent challenges in the modulation of local reaction environment, encompassing local pH, the choice of the species and concentrations of cations and anions as well as local reactant/intermediate concentrations, for achieving high C2+ selectivity. In addition, mechanistic understanding in the effects of the local reaction environment is also discussed. Particularly, the important progress extracted from in situ and operando spectroscopy techniques provides insights into how local reaction environment affects C−C coupling and key intermediates formation that lead to reaction pathways toward a desired C2+ product. The possible future direction in understanding and engineering the local reaction environment is also provided.

Unraveling the Mechanisms of Zirconium Metal–Organic Frameworks‐Based Mixed‐Matrix Membranes Preventing Polysulfide Shuttling

Lithium–sulfur batteries are considered as promising candidates for next‐generation energy storage devices for grid applications due to their high theoretical energy density. However, the inevitable shuttle effect of lithium polysulfides and/or dendrite growth of Li metal anodes hinder their commercial viability. Herein, the microporous Zr fumarate metal–organic framework (MOF)‐801(Zr) is considered to produce thin (≈15.6 μm, ≈1 mg cm2) mixed‐matrix membranes (MMM) as a novel interlayer for Li–S batteries. It is found that the MOF‐801(Zr)/C/PVDF‐HFP composite interlayer facilitates Li+ ions diffusion, and anchors polysulfides while promoting their redox conversion effectively. It is demonstrated that MOF‐801 effectively trapped polysulfides at the cathode side, and confirmed for the first time the nature of the interaction between the adsorbed polysulfides and the host framework, through a combination of solid‐state nuclear magnetic resonance and molecular dynamics simulations. The incorporation of MOF‐801(Zr)/C/PVDF‐HFP MMM interlayer results in a notable enhancement in the initial capacity of Li–S batteries up to 1110 mA h g−1. Moreover, even after 50 cycles, a specific capacity of 880 mA h g−1 is delivered.